The boot process in closer look

You can boot Linux either from a floppy or from the hard disk. The installation section in the Installation and Getting Started guide ([Wel]) tells you how to install Linux so you can boot it the way you want to.

When a PC is booted, the BIOS will do various tests to check that everything looks all right, and will then start the actual booting. It will choose a disk drive (typically the first floppy drive, if there is a floppy inserted, otherwise the first hard disk, if one is installed in the computer; the order might be configurable, however) and will then read its very first sector. This is called the boot sector; for a hard disk, it is also called the master boot record, since a hard disk can contain several partitions, each with their own boot sectors.            

The boot sector contains a small program (small enough to fit into one sector) whose responsibility is to read the actual operating system from the disk and start it. When booting Linux from a floppy disk, the boot sector contains code that just reads the first few hundred blocks (depending on the actual kernel size, of course) to a predetermined place in memory. On a Linux boot floppy, there is no filesystem, the kernel is just stored in consecutive sectors, since this simplifies the boot process. It is possible, however, to boot from a floppy with a filesystem, by using LILO, the LInux LOader.    

When booting from the hard disk, the code in the master boot record will examine the partition table (also in the master boot record), identify the active partition (the partition that is marked to be bootable), read the boot sector from that partition, and then start the code in that boot sector. The code in the partition's boot sector does what a floppy disk's boot sector does: it will read in the kernel from the partition and start it. The details vary, however, since it is generally not useful to have a separate partition for just the kernel image, so the code in the partition's boot sector can't just read the disk in sequential order, it has to find the sectors wherever the filesystem has put them. There are several ways around this problem, but the most common way is to use LILO. (The details about how to do this are irrelevant for this discussion, however; see the LILO documentation for more information; it is most thorough.)          

When booting with LILO, it will normally go right ahead and read in and boot the default kernel. It is also possible to configure LILO to be able to boot one of several kernels, or even other operating systems than Linux, and it is possible for the user to choose which kernel or operating system is to be booted at boot time. LILO can be configured so that if one holds down the alt, shift, or ctrl key at boot time (when LILO is loaded), LILO will ask what is to be booted and not boot the default right away. Alternatively, LILO can be configured so that it will always ask, with an optional timeout that will cause the default kernel to be booted.

With LILO, it is also possible to give a kernel command line argument, after the name of the kernel or operating system.

META: The are other boot loaders than LILO. Information about them will be added in some future version. loadlin.

Booting from floppy and from hard disk have both their advantages, but generally booting from the hard disk is nicer, since it avoids the hassle of playing around with floppies. It is also faster. However, it can be more troublesome to install the system to boot from the hard disk, so many people will first boot from floppy, then, when the system is otherwise installed and working well, will install LILO and start booting from the hard disk.

After the Linux kernel has been read into the memory, by whatever means, and is started for real, roughly the following things happen:

• The Linux kernel is installed compressed, so it will first uncompress itself. The beginning of the kernel image contains a small program that does this.    

• If you have a super-VGA card that Linux recognizes and that has some special text modes (such as 100 columns by 40 rows), Linux asks you which mode you want to use. During the kernel compilation, it is possible to preset a video mode, so that this is never asked. This can also be done with LILO or rdev .        

• After this, the kernel checks what other hardware there is (hard disks, floppies, network adapters...), and configures some of its device drivers appropriately; while it does this, it outputs messages about its findings. For example, when I boot, I it looks like this:        

  LILO boot:
  Loading linux.
  Console: colour EGA+ 80x25, 8 virtual consoles
  Serial driver version 3.94 with no serial options enabled
  tty00 at 0x03f8 (irq = 4) is a 16450
  tty01 at 0x02f8 (irq = 3) is a 16450
  lp_init: lp1 exists (0), using polling driver
  Memory: 7332k/8192k available
   (300k kernel code, 384k reserved, 176k data)
  Floppy drive(s): fd0 is 1.44M, fd1 is 1.2M
  Loopback device init
  Warning WD8013 board not found at i/o = 280.
  Math coprocessor using irq13 error reporting.
  Partition check:
    hda: hda1 hda2 hda3
  VFS: Mounted root (ext filesystem).
  Linux version 0.99.pl9-1 (root@haven) 05/01/93 14:12:20

  The exact texts are different on different systems, depending on the hardware, the version of Linux being used, and how it has been configured.

• Then the kernel will try to mount the root filesystem. The place is configurable at compilation time, or any time with rdev  or LILO. The filesystem type is detected automatically. If the mounting of the root filesystem fails, for example because you didn't remember to include the corresponding filesystem driver in the kernel, the kernel panics and halts the system (there isn't much it can do, anyway).            

  The root filesystem is usually mounted read-only (this can be set in the same way as the place). This makes it possible to check the filesystem while it is mounted; it is not a good idea to check a filesystem that is mounted read-write.      

• After this, the kernel starts the program init  (located in /sbin/init ) in the background (this will always become process number 1). init  does various startup chores. The exact things it does depends on how it is configured; see chapter 7 for more information (not yet written). It will at least start some essential background daemons.  

• init  then switches to multi-user mode, and starts a getty  for virtual consoles and serial lines. getty  is the program which lets people log in via virtual consoles and serial terminals. init  may also start some other programs, depending on how it is configured.        

• After this, the boot is complete, and the system is up and running normally.